Latest Brocade 143-080 Exam Dumps Free Download with PDF & VCE (41-50)

QUESTION 41
You need to run the Diagnostic Port test on a long distance FC link. Which statement is true?

A.    The ISL link can stay online.
B.    The test is supported when the port configured as a Diagnostic Port is connected to a storage port.
C.    The test can be used to test the ICL ports on the Brocade DCX 8510-8.
D.    The test can be used to measure link distance.

Answer: D

QUESTION 42
You have deployed Brocade FX8-24 blades. You have decided to set up several FCIP links between the data centers. Which three port configurations are available for simultaneous use on each blade? (Choose two)

A.    two 10 Gbps ports and ten 1 Gbps ports
B.    one 10 Gbps port and ten 1 Gbps ports
C.    ten 1 Gbps ports
D.    two 10 Gbps ports and two 1 Gbps ports
E.    two 10 Gbps ports

Answer: BE

QUESTION 43
Your company must migrate data to a new data center 100 km away. You decide to use an FCIP- shared infrastructure instead of dark fiber. What are two advantages? (Choose two)

A.    less fiber is required
B.    FCIP leverages your investment in the IP infrastructure
C.    FCIP has less protocol overhead
D.    FCIP uses jumbo frames

Answer: AB

QUESTION 44
You were asked to use the portcfgfillword command to configure a long distance link between two Brocade 6510s. Which two statements are true? (Choose two)

A.    It is not supported on Condor 2-based platforms
B.    It is not supported on Condor 3 based platforms
C.    It is only supported on an 8 Gbps port of Condor 2
D.    It is only supported on a 16 Gbps port on Condor 3

Answer: BC

QUESTION 45
You have configured an FCIP link between two remote data centers. Adaptive Rate Limiting has been configured on this link.When TCP retransmits are detected on the link, what will happen to the committed rate?

A.    It will increase to the set maximum
B.    It will drop to the set minimum
C.    It will reset to default configuration
D.    It will increase

Answer: B

QUESTION 46
You are using FC routing to allow a host in the edge fabric with FID 10 to communicate with the target in the edge fabric with FID20. The Backbone FID is 100. The host is unable to communicate with target. Referring to the exhibit, which statement is true?

image

A.    The host is offline
B.    The target is offline
C.    LSAN zones have not been configured on the edge fabric FID 10
D.    LSAN zones have been configured on the backbone fabric

Answer: B

QUESTION 47
You observed that one of your Brocade DCX 8510-8s experienced a failover. You logged into the switch and ran errshow to determine why the failover occurred, but nothing besides the failover message was displayed. What is the reason no other messages are shown?

A.    You need to use the ?a option to display all messages.
B.    The output of the command is unique for each control processor.
C.    You need to run the ?r option to obtain a revised output.
D.    The output of the command is unique for each core blade.

Answer: C

QUESTION 48
You are using FC routing to allow a host in the Backbone with FID 10 to communicate with the target in the edge fabric with FID 100. The host is unable to communicate with the target.
Which statement is true?

image

A.    The host is offline
B.    The target is offline
C.    LSAN zones have not been configured on the edge fabric
D.    LSAN zones have not been configured on the backbone fabric

Answer: C

QUESTION 49
Refer to the Exhibit. What prevents host H1 from communicating with target T2?

image

A.    The FIDs are misconfigured
B.    All devices in single LSAN can only be from two fabrics
C.    The LSAN zones are misconfigured
D.    The LSAN zone names must match on all fabrics

Answer: A

QUESTION 50
Refer to the Exhibit. What prevents host H1 from communicating with the target T2?

image

A.    The corresponding LSAN zone names must match in each of the fabrics
B.    All devices in a single LSAN can only be from two fabrics
C.    You need to use Node WWNs for your devices in LSAN zones
D.    The LSAN zone configuration on FID is incorrect

Answer: A

If you want to pass the Brocade 143-080 exam sucessfully, recommend to read latest Brocade 143-080 Dumps full version.